singer simple 3116 handwheel stuck

I took the bobbin area apart. This sets the machine to its "bobbin winding" mode. There are a whole lot of problems you can fix yourself. Too, for the hand wheel to have come off and flown across room there had to have been considerable force from inside the machine, indication a very serious part(s) failure. Here is a great site that will walk you through the repair of the handwheel and how to unjam it. Then if your Singer still doesnt work, take it to a qualified and approved Singer repairman. I took the bobbin case out, and it still does the same thing so it doesn't have to do with that. Standard needle threading instructions still apply when you use an automatic threader. 282Feedbacks. Continue sliding the thread through that slit until it slips under the finger of the case. Unlock the spindle by pushing it back to the left. The first place to look when this happens is the bobbins location. Put the sewing machine oil nozzle against the motor shaft (a long arm that goes up and down) and squirt a drop of oil. After you have made the necessary repairs or did the oiling retrace your steps by putting the motor back in place and screw in all the screws. We use cookies and similar technologies on our website. Two other sources for this problem could be that you forgot to clean and lubricate the machine. Turn the handwheel until the needle is fully raised. This component requires regular oiling to function correctly, especially when you have used the machine for many consecutive hours. The best thing to do in this situation is re-threading the needle as per the instructions of the manufacturer for your sewing machine; lift the presser foot to do this. Sometimes, tension is good. The cover will open but will not detach. To learn more about how we use cookies. The hand wheel of my Singer 7465 sewing machine popped right off and flew across the room. Possible Reasons for the Jammed Sewing Machine Handwheel, The Steps to Fix A Hard to Turn Sewing Machine Handwheel, 1. This manual is available in the following languages: English. 949Feedbacks, Silver Feedback Medal for All Time! The first step in solving this issue is to set your stitch length settings, width, and length, back to their previous position before the problem began. While youre allowed to rotate the handwheel in a clockwise motion to unlock the bobbin, you need to do it in an extremely subtle way. Many stitch problems would qualify under this heading. Then check your tension and threading to make sure they are okay. If it has been a while then the lack of oil and cleaning may be the culprit. With the thread held in place by the thread guide, wind the thread clockwise around the bobbin winder tension discs in front of the guide. To make sure your old sewing machines handwheel isnt jammed due to how the smaller wheel is positioned inside it, adjust the inner knob of the handwheel as the first step in fixing a sewing machine handwheel that is hard to turn. She learned from her grandma and never stopped. Turn your handwheel until the needle is all the way up and pull on the hinged tap until the bobbin case comes out. This also happens when you don't have the correct size of needle or type of thread for the material, so make sure you check that as well! After inserting the thread through the take-up lever, pull it back down through the left channel again. If they are not in their right spot this may be the problem. The foot pedal will engage and allow the machine to receive the power to move the needle to sew. If you are using a small spool of thread, place the cap on the pin so that the small side is next to the spool. Set the thread level to the highest before pulling the thread pool throughout the machines tension disc. Use the brush supplied to clean the area. Incorrect threading is a mistake that both beginners and intermediate sewers make. Have a singer simple 3116 machine. All tip submissions are carefully reviewed before being published. Feed the thread through from the inside so that the tail is still on the outside of the bobbin. A screw driver will come with the machine. No, you should not use sewing machines constantly for many hours, especially for older-generation gadgets. 4. I do vintage repairs here in Scotland for my sewing students, and can promise you there is so much 'tricky' to repairing a sewing machine it's not worth risking the machine to try a home repair. Over time, the built-up lint and dirt will obstruct the hand wheels movement and wear it down. Close the cover when done by pushing it back up and into place. The other is on the underside of the machine. Fitting a spring loaded darning or free-motion embroidery foot, It is still looping under the fabric, then jams, Stitches are not formed properly while sewing, Irregular stitches while using my sewing machine, My sewing machine is missing skipping stitches, Thread looping, reveling or bunching under fabric while sewing, Knocking noise then machine becomes jammed, No power machine not moving and light not working, Sewing machine suddenly stops during sewing, Technical Sewing Machine Problem and Repair, Embroidery software and which format do I need advice. If you have the wrong needle, it is in backward, not fully inserted or if the thread is too thick or thin for the needle these will all cause the bobbin to not spin. So I've had this sewing machine forever and I can typically fix whatever is wrong with it. If it is at the back, take it off as well. My machine is not raising the bobbin thread. I posted an answer to this back in December but I see it's not showing - if you haven't given up on this machine, it's a fairly simple fix for a repair tech - your bobbin gear has 'died'. With some models you may have to first pull the knob to be able to move it and with a new model of sewing machine the hand wheel can't be locked because it is not necessary as the hand wheel is not used anymore to wind a bobbin. Presser foot maybe in up position, a lot of modern machines will not work until the presser foot is lowered - check and lower foot. What is wrong? Ove time, this leads to the sewing machine losing its viscidity. If so you need to take the appropriate steps to untangle it. Squirt a drop of oil against any moving cog, wheel or part. To adjust it you should remove the presser foot and remove the needle plate. You can manage your cookie settings via your browser setting at any time. One threads R to L, one L to R and the Elna from the front. {"smallUrl":"https:\/\/www.wikihow.com\/images\/thumb\/1\/10\/Thread-a-Singer-Simple-3116-Step-1.jpg\/v4-460px-Thread-a-Singer-Simple-3116-Step-1.jpg","bigUrl":"\/images\/thumb\/1\/10\/Thread-a-Singer-Simple-3116-Step-1.jpg\/aid5546371-v4-728px-Thread-a-Singer-Simple-3116-Step-1.jpg","smallWidth":460,"smallHeight":345,"bigWidth":728,"bigHeight":546,"licensing":"